Return to Website

SWEPTLINE CD's $20 Check or Money order to:James Megee1483 Perkins LaneEdgewater Park NJ 08010 or Paypal to: jmegee57@hotmail.comSee the CD page at http://www.olddodges.com/sweptlinecd.htm

61-71 Glove boxes, Core Support/Radiator seals, 69-71 Tool Stowage Decals, 69-71 Firewall Insluation Pads, and A100 glove boxes.Contact Gary Offill for pricing and info at gwo1988@yahoo.com
  
The '61-'71 Dodge Sweptline Truck Forum #36

The Official Forum of the DTA. Here's your place to talk about Dodge trucks made from 1961-1971. The Truck of The Week was submitted by Aaron. To view the DTA Photo Albums, click on the "Return to Website" link below. To view DodgeSweptline.Org, click on "DTA HOME"  Best viewed in 1024x768 Not affiliated with Chrysler LLC. Dodge is a registered trademark of Chrysler LLC

      


Return to Website

  Reply
  Home

Subject:   Re: Re: Swepty load center/terminal block info....
Name:   MoparNorm
Date Posted:   Dec 2, 08 - 5:37 AM
IP Address:   71.104.149.239
Email:   moparnorm@hotmail.com
Dodge-Link   http://grabdemocracybythehorns.com/
Message:   That's what I always thought, but according to Russ, Jim and Terry, there is an equal chance of arching from either terminal.
However since there is no chance of a short when a tool touches a ground while working on the ground, therefore you remove the negative* side first, to terminate, or "safe" the circuit.



*assumes that you have a negative ground system and don't have a wrench long enough to make contact with both the negative post and the positive post simultaneously.
Replies:    
Re: Re: Re: Swepty load center/terminal block info.... by Russ Roth · Dec 2, 08 - 6:55 AM
Re: Swepty load center/terminal block info.... by PwrWgnDrvr · Dec 2, 08 - 6:17 AM
Re: Re: Swepty load center/terminal block info.... by Russ Ashley · Dec 2, 08 - 9:25 AM
Re: Re: Re: Swepty load center/terminal block info.... by JimmieD · Dec 2, 08 - 11:00 AM
Re: Re: Re: Re: Swepty load center/terminal block info.... by Russ Ashley · Dec 2, 08 - 12:42 PM
Re: Charge or Holes? by PwrWgnDrvr · Dec 2, 08 - 7:26 PM
Re: Re: Charge or Holes? by JimmieD · Dec 2, 08 - 9:04 PM
Re: Re: Re: Charge or Holes? by PwrWgnDrvr · Dec 2, 08 - 10:31 PM
Re: Re: Re: Re: Charge or Holes? by JimmieD · Dec 3, 08 - 9:29 AM
Now we see by PwrWgnDrvr · Dec 3, 08 - 7:19 PM
Re: If the point was as u say by PwrWgnDrvr · Dec 2, 08 - 6:57 PM
Re: U misunderstand your linked article by PwrWgnDrvr · Dec 2, 08 - 7:08 PM
Re: Bigger spark on Pos or Neg? by PwrWgnDrvr · Dec 2, 08 - 7:14 PM
Re: Re: Bigger spark on Pos or Neg? by JimmieD · Dec 2, 08 - 9:02 PM
Good point by Russ Ashley · Dec 3, 08 - 4:43 AM
Re: Good point by MoparNorm · Dec 4, 08 - 4:13 AM
Re: Re: Good point by MoparNorm · Dec 4, 08 - 4:14 AM
Re: Re: Re: Good point by PwrWgnDrvr · Dec 4, 08 - 6:26 AM
Re: Re: Re: Swepty load center/terminal block info.... by Russ Roth · Dec 2, 08 - 12:36 PM
This Has All Been One Big Load Of B.S. Information...... by Hobcobble · Dec 6, 08 - 5:19 AM


  Reply
  Home


powered by Powered by Bravenet bravenet.com