Posted by Tom in Indiana [216.249.64.39] on Saturday, August 01, 2015 at 19:51:30 :
In Reply to: Re: U-joint help. posted by Todd (California) [70.214.35.129] on Saturday, August 01, 2015 at 19:37:42 :
Taken from the archives:
GROUP 6 - PROPELLER SHAFT/U-JOINT
***********************************VC/VF/WC******WC3/4********WC1.5******WDX******B1-3*****C1-4****W300****W300M***WM300*****M37/M37B1/M43**
INTERMEDIATE SHAFT * * * * * * * *
FRONT/REAR PROPELLER SHAFTS * * * * * * * *
INTERMEDIATE SHAFT – NAPA# PUJ304 , Precision# 304, Neapco# 3-0056, AutoZone# 3-0056DL(3” Inside Lockup x 1.232” Brg. Cup) [WC, WDX, PW and
M37]
FRONT/REAR PROPELLER SHAFTS – NAPA# PUJ305, Precision# 305, Neapco# 2-1400, AutoZone# 2-1400DL (2” Inside Lockup x 1.231” Brg. Cup) [WC, WDX, PW and M37
Other Dodge Trucks
INTERMEDIATE/FRONT/REAR 1958 – 1960 ½ Ton – NAPA# NPJP315G, Neapco# 1-6301 (2.125” Inside Lockup x 1.078” Brg. Cup)
All Wheel Joints – Inside Lockup – NAPA# PUJ365, Neapco# 1-0174 (2.188” x 1.063” Brg. Cup)
All Wheel Joints – Outside Lockup – NAPA# PUJ355, Neapco# 2-0053 (3.622” Outside Lockup x 1.188” Brg. Cup)
INTERMEDIATE/FRONT/REAR 1961 – 1971 ½ Ton – NAPA# NPJP429, Neapco# 1-5900 (2.380” Inside Lockup x 1.063” Brg. Cup)
All Wheel Joints – Inside Lockup – NAPA# PUJ365, Neapco# 1-0174
All Wheel Joints – Outside Lockup – NAPA# PUJ355, Neapco# 2-0053
INTERMEDIATE/FRONT/REAR 1972 – 1974 ½ Ton – NAPA# NPJP315G, Neapco# 1-6301 (2.125 Inside Lockup x 1.078” Brg. Cup)
All Wheel Joints 1972 – 1974 – NAPA# NPJP371, Neapco# 1-0297 (2.188” Inside Lockup x 1.188” Brg. Cup)
INTERMEDIATE/FRONT/REAR 1961 – 1974 ¾ Ton – NAPA# NPJP315G, Neapco# 1-6301
All Wheel Joints 1972 – 1974 – NAPA# NPJP371, Neapco# 1-0297
All Wheel Joints – Inside Lockup – NAPA# PUJ365, Neapco# 1-0174 (2.188” Inside Lockup x 1.063” Brg. Cup)
All Wheel Joints – Outside Lockup – NAPA# PUJ355, Neapco# 2-0053
INTERMEDIATE 1961 – 1967 ¾ Ton – NAPA# PUJ304, Neapco# 3-0056
Front/Rear 1961 – 1967 ¾ Ton – NAPA# PUJ304, Neapco# 3-0056
All Wheel Joints – Inside Lockup – NAPA# PUJ365, Neapco# 1-0174
All Wheel Joints – Outside Lockup – NAPA# PUJ355, Neapco# 2-0053
INTERMEDIATE/FRONT/REAR 1958 1 Ton – NAPA# PUJ423, Neapco# 2-6200 (2.562” Inside Lockup x 1.188” Brg. Cup)
Rear – NAPA# PUJ316, Neapco# 2-1175 (2.622” Inside Lockup x 1.126” Brg. Cup)
INTERMEDIATE/FRONT/REAR 1959 - 1974 1 Ton – NAPA# PUJ304, Neapco# 3-0056
INTERMEDIATE 1972 1 Ton – NAPA# PUJ316, Neapco# 2-1175
WINCH DRIVE SHAFT
Front UJ
(UP TO Ser. No. 88759859) - Rockwell# 1FR, Precision# 853, Spicer# 5-264X (2.850” Cap-to-Cap x .875” Brg. Cup) Requires machining .015+off outside end of bearing cross and .015+ off outside end of Brg. Cup, or silicone seal around the cup and .015+ shim under the lock plate cut for cup/bolt holes) [WC, and WDX]
(After Ser. No. 88759859) - Neapco# 1-0170 (1.5” inside lockup X .938 dia. Cap), New Holland #39360 (PW/M37)
Dodge ½ (58-74), ¾ (61-67), and 1 Ton (129, 133 W.B.) Models - Neapco# 1-0170 (1.500” Inside Lockup x .938” Brg. Cup)
Rear UJ
(UP TO Ser. No. 88759859) - Rockwell# 1FR, Precision# 853, Spicer# 5-264X (2.850” Cap-to-Cap x .875” Brg. Cup) Requires machining .015+off outside end of bearing cross and .015+ off outside end of Brg. Cup, or silicone seal around the cup and .015+ shim under the lock plate cut for cup/bolt holes) [WC, and WDX]
(After Ser. No. 88759859) - Neapco# 1-0170 (1.5” Inside Lockup X .938” Brg. Cup) [PW, and M37]
Dodge ½ (58-74), ¾ (61-67), and 1 Ton (129, 133 W.B.) Models - Neapco# 1-0170 (1.500” Inside Lockup x .938” Brg. Cup)
PTO Rear Drive Shaft - Neapco# 2-1400 (2” Inside Lockup x 1.231” Brg. Cup) [WDX, and PW]
Sliding Yoke
Oil Seal * * * * * * * * * *
Oils Seal Washer * * * * * * * * * *
Cap * * * * * * * * * *
PROPELLER SPLINED/SLIDING YOKES
Differential Pinion * * * * * * * *
Transmission * * * * * * * *
Transmission Hand Brake ** * * * * * * *
Transfer Case * * * * * * * *
(* - Use WC 3/4 when coverting rear end to a center differential setup, swap out existing TC hand brake companion yoke)
Follow Ups: